How Much Does an Epoxy Floor Cost in Steveston?

In Steveston, professionally installed floors start at $7 per square foot for epoxy vinyl flake, $13 for quartz, and $16 for metallic. A standard two-car garage starts around $2,800 — fully prepped, coated, and backed by the Wish Warranty.

2026 epoxy floor prices in Steveston at a glance

Most quotes you'll get in the Lower Mainland come as a wide "$6–$15" range with no detail. Here's a clearer way to think about it — by the coating system you actually choose:

Prices shown are 2026 starting averages for the Steveston area and are subject to change. Your final quote depends on floor size, condition, and the system you choose — confirmed at a free in-person estimate.

Epoxy floor cost by garage size

The most common question we hear in Steveston is simply "what will my garage cost?" Using our entry epoxy-flake rate of $7/sq ft, here's a realistic starting range by garage size:

Starting figures based on the low end of each size at $7/sq ft. Quartz and metallic systems, added crack or moisture repair, and premium colours raise the total. These are averages and subject to change — your written estimate is always exact.

Flake vs quartz vs metallic — what am I paying for?

The price gap between systems isn't random. It reflects the materials, the labour, and the look. Here's the plain-language version:

What's included in your price — and what can change it

Our starting rate isn't a "paint-and-run" number. A Wish floor includes professional preparation, which is the single biggest reason coatings last instead of peel:

• Diamond grinding to open the concrete so the coating bonds mechanically, not just sits on top.
• Crack and joint repair so old damage doesn't telegraph through the finish.
• Full coating system — base coat, full flake (or quartz/metallic), and a polyaspartic topcoat.
• Cleanup and a next-day walk-on floor — most jobs are done in about two days.

A few things move the number up from the starting rate: the system you choose (quartz and metallic cost more than flake), the condition of your slab (heavy cracking, pitting, or oil saturation), moisture issues that need a barrier, and total square footage. We flag all of this honestly at the estimate — no surprises after the deposit.

How we install a floor that lasts

Longevity comes from preparation, not paint. Every Wish floor in Steveston follows the same disciplined sequence:

1. Free on-site assessment. We measure the space and check the slab for cracks, pitting, moisture signs, and any old coating that needs removing.
2. Diamond grinding. We profile the concrete with a diamond grinder so the coating bonds mechanically — the step that stops peeling down the road.
3. Crack & joint repair. Cracks, control joints, and spalls are filled and levelled before any colour goes down.
4. Base coat + full broadcast. An epoxy (or quartz/metallic) base coat, with a full broadcast of vinyl flake where selected.
5. Polyaspartic topcoat. A hard-wearing, UV-stable topcoat seals the floor — walk on it the next day, with most jobs done in about two days.

All work is carried out to WorkSafeBC standards, and we follow BC Building Code guidance for slab moisture on every job.

Estimate your own cost in one line

Not sure of your square footage? A single-car garage is usually 200–300 sq ft and a double is 400–600 sq ft. We measure precisely at your visit, so the number on your quote is the number you pay.

Serving Steveston — local conditions & coverage

Steveston is Richmond’s historic fishing village at the southwest tip of Lulu Island, where the Fraser meets the Strait of Georgia. Between the heritage homes near the boardwalk and the newer builds inland, slabs here sit on low delta ground — so a moisture-aware assessment and a hard-wearing polyaspartic topcoat matter more than almost anywhere in the region.

Neighbourhoods we cover:

Serving the V7E postal areas and surrounding streets. Not sure if we reach you? Ask for a free estimate — if we can get there, we’ll quote it.

Water table, slab moisture & why we recommend a vapour barrier

Steveston sits at the mouth of the Fraser River on Lulu Island, built on soft delta silt only a metre or so above sea level and protected by dikes. Ground water sits close to the surface across the village, which matters more than most homeowners expect once you’re coating a concrete floor.

Concrete is porous, and where the water table sits close to the surface, ground moisture is drawn up through the slab as vapour — a process called moisture vapour transmission (MVT). You often can’t see it, but that rising vapour is one of the most common reasons floor coatings fail: it builds pressure under the coating and pushes it off the slab, showing up as bubbling, whitening, or peeling months after the job looked perfect. In the coatings trade it’s well understood that most failures trace back to moisture, not a bad product.

That’s why, on low-lying delta slabs like these, we recommend a moisture-vapour-barrier primer. It’s a dedicated primer that seals the concrete and holds back rising vapour before the colour and topcoat go on, so the finish bonds and stays put. Slab moisture is measured with standard tests (ASTM F1869 and F2170); where the readings are high, the barrier isn’t an upsell — it’s the difference between a floor that lasts and one that lifts.

We check every slab for moisture at your free estimate and tell you honestly whether yours needs it.

Frequently asked questions

How much does an epoxy garage floor cost in Steveston?

Epoxy vinyl flake starts at $7 per square foot, so a two-car garage starts around $2,800. Quartz starts at $13 and metallic at $16 per square foot. Your final price depends on size, floor condition, and the system you choose.

What's the difference between epoxy flake, quartz, and metallic?

Flake is the durable everyday finish (from $7/sq ft). Quartz adds grip for wet areas like bathrooms and outdoor showers (from $13). Metallic creates a high-gloss, one-of-a-kind showpiece (from $16). All three are sealed with a polyaspartic topcoat.

How much is a two-car garage floor?

A two-car garage in Steveston starts at about $2,800 for epoxy vinyl flake, based on a 400-square-foot floor at $7 per square foot. Larger or damaged floors cost more; we confirm the exact price at your free estimate.

Why does professional epoxy cost more than a DIY kit?

A DIY kit skips diamond grinding, crack repair, and a professional-grade topcoat — the steps that stop peeling. Wish floors are fully prepped, installed in about two days, and backed by a 20-year colour and adhesion warranty on concrete.

What affects my final epoxy floor price?

Size, the coating system, your slab's condition, crack and moisture repair, and your colour choice. Most Steveston garages fall within our starting ranges; we give you a firm, no-obligation number at your in-person estimate.

Do you install epoxy floors near Steveston?

Yes. We coat floors across Steveston, Richmond, and the wider Lower Mainland. Book a free in-person estimate and we’ll bring physical colour samples to your home.